Jump to content
HWBOT Community Forums

Search the Community

Showing results for tags 'guide'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • HWBOT News
  • HWBOT Information
    • HWBOT World Tour
    • HWBOT Competitions
    • Benchmark Rules
    • Intel XTU HWBOT Integration
    • HWBOT Development: bugs, features and suggestions
    • HWBOT Software and Apps
    • Submission & member moderation
    • HWBOT OC-Crime Center
    • OC Archeology
  • Members Lounge
    • HWBOT Team Forum RSS
    • Rookies Help Rookies
    • League Discussions
    • Result Discussions
    • Member Discussions
    • Team Discussions
    • Announce event and group sessions
  • Overclocking & benchmarking
    • General hardware discussion
    • General overclocking
    • Intel CPU Overclocking
    • AMD CPU Overclocking
    • GPU Overclocking and Tweaking
    • Nvidia GPU Overclocking
    • AMD GPU Overclocking
    • Casemodding and Rig Aesthetics
    • ARM Overclocking (Raspberry Pi and other devices)
    • Benchmark software
  • Advanced overclocking
    • Extreme overclocking
    • Memory Heaven (air/extreme)
    • Volt modifications
    • Elmor's Lab
  • Offtopic
    • Offtopic
    • HWBOT Marketplace
    • VR Hardware and System Builds
  • Open Benchtable Forum
    • OBT / BC1 Discussion
    • After Sales Support
  • Support
    • Support
    • HWBOT internationalization

Calendars

  • Community Calendar

Blogs

  • CPU reviews

Found 1 result

  1. This is a guide on how to raise the target power limit of your GTX 1080 with a resistor mod. In my case, I used an EVGA GTX 1080 FE. Your card can differ from mine. I am new to forums (actually this is my first informative post) so I hope it'll help you. Feedback always welcome! After doing some research about modding the shunt resistor on GTX video cards to raise power limits, I decided to do skip the liquid metal part because the composition of this metal could damage the resistor/tin and there is also a chance that the liquid metal could drip off the shunt and short other components. But beware that this is basically a permanent mod and can hardly be reversed. Also, some soldering and electrical skills needed! Figure 1 What I did is soldering another resistor parallelly on top of the shunt resistor. The reason for soldering a resistor parallelly instead of replacing is because we are working with a very low resistance (1mΩ = 0,001Ω), and putting your own calculated resistor with too much soldering tin will create an even bigger resistance where you can't know the exact resistance. Here you can see why: Figure 2 & 3 The two bigger pads are where the current is mostly running trough and two tiny pads that are connected to the power measurement circuit. It's important to keep the resistor as close as possible to the sensing pads for a more accurate measure. I hear you thinking: but you are also raising the resistance if your soldering a resistor on top of it, isn't that the same? Not exactly, because if your value is not correct you can carefully solder it off and replace it with another value (I recommend to calculate it right at once). in brief, It's definitely an important aspect to think of if you are working with low resistance's. As you can see in figure 1 I soldered a 6mΩ 1% resistor on top of the existing 2mΩ resistor, raising the card's power limit by 25%. I will explain how I calculated that. I used the common formula for calculating parallel resistance : Figure 4 In my case, I wanted to raise a maximum of 25% of the power limit. That's going to be: 2mΩ / 100% * 25% = 0.5mΩ subtracting that from 2mΩ = an Rtot of atleast 1,5mΩ. R1 = 2mΩ Rtot = 1,5mΩ We want to know R2 so the formula becomes: = 6mΩ Figure 5 After that, I assembled the card back together and tested it with Furmark. Before the mod: Figure 6 After the mod: Figure 7 As you can see I gained a fair amount of core clock, and also the VDDC has more room to increase. I actually did need to lower the core overclock because it was running too fast and began to crash. The tests were running quite short which is why the card was not running hot. But I'm not sensing any extreme temperatures on the longer runs (30 mins on 100% fan speed), but this could be that I used liquid metal on the GPU die: Figure 8 & 9 Now, you can extend it further than 25% but be aware that your card can run very hot or even blow up. So if you are planning to do this, calculate the resistance well, use a more extreme cooling solution (like custom water cooling) and keep a good eye on the temps so that the risks are minimalized. After all, it's a limit to protect the card from breaking. Do it at your own risk. Thank you for your time, I hope it was helpful. I will start shortly on my first hardline water cooling build which I will post pictures of too. Yours sincerely, Graxx Sorry for my bad English, I'm dutch. My sources: Google is your best friend der8auer's video:
×